Skip to main content

On the first day of water damage restoration, the crew finds and stops the source, checks for safety hazards, measures how far the water has spread, documents the damage, extracts standing water, removes materials that cannot be dried, and sets up drying equipment. You should finish the day with a clear plan and machines running.

Fife and Milton sit side by side where the Puyallup River valley opens toward Commencement Bay. Fife spreads across the flat valley floor along Interstate 5, and Milton climbs from that same floor up the hillside and across the Pierce and King county line. Homes in both towns range from older ramblers to newer townhomes and apartments.

November is when water losses start to stack up here. Long rains soak the ground, the first cold nights test outdoor plumbing, and furnaces and water heaters run harder than they have since spring. When something gives, the first day of restoration sets the tone for everything that follows.

What happens when the crew first arrives?

They start with safety and the source. Before any equipment comes in, the crew lead walks the house with you, asks what happened, and looks for the reason the water is there.

Expect questions like these:

  • When did you first notice the water?
  • Where did it come from: a supply line, an appliance, the roof, the ground, or a drain?
  • Has the water been shut off at the main valve or the fixture?
  • Are any outlets, cords or appliances wet?
  • Has anyone been walking through the wet areas?

If the source is still active, stopping it comes first. That may mean closing the main shutoff, isolating a fixture, or tarping a roof opening. If water has reached electrical outlets or the panel, power to those areas gets shut off before anyone works in them.

How does the crew figure out how far the water went?

With moisture meters and thermal imaging, not just by looking. Water travels farther than it appears. It wicks up drywall, runs under baseboards, spreads beneath vinyl and laminate floors, and soaks into the subfloor below carpet.

The crew takes readings in the wet room, then keeps going into hallways, closets and neighboring rooms until the readings come back dry. They mark the edges of the wet area so everyone can see where drying needs to happen. In a two-story home, they also check the ceiling and walls below any leak on the upper floor.

This mapping step is what separates real drying from guesswork. A room can look dry by evening and still have wet framing behind the wall.

What gets documented on day one?

Nearly everything. Good documentation protects you and makes the rest of the project easier to follow.

  • Photos and video of each affected room before work begins
  • Moisture readings with locations, written down or logged in software
  • A note of the water source and when it was stopped
  • A list of materials removed and why
  • Equipment placed, where it is, and when it was set

Your insurance company may ask for this kind of record. Restoration companies document the job to support your claim, but your insurer decides what your policy covers, so it is worth calling them early and asking what they need.

How is the water removed?

Standing water comes out first with truck-mounted or portable extraction equipment. On carpet, crews use extraction tools that pull water out of both the carpet and the pad. On hard floors, they use squeegees and wet vacuums. In crawl spaces, they may use pumps.

The more water that comes out by extraction, the less the drying equipment has to pull out of the air later. That is why this step takes time and is done carefully, room by room.

What materials get removed on the first day?

Anything that cannot be dried in place, or that holds water against the structure. Common examples include:

  • Soaked carpet pad, which acts like a sponge under the carpet
  • Baseboards, so air can reach the bottom of the drywall
  • The bottom section of drywall when it is saturated, sometimes called a flood cut
  • Wet insulation inside walls or under floors
  • Cabinet toe kicks, so air can reach under the cabinet base

The type of water matters too. Clean water from a supply line allows more materials to be dried and kept. Water from a drain, a toilet overflow or flooding from outside has been in contact with contaminants, so more porous materials are removed. Your crew should explain which category they think applies and why.

How is the drying equipment set up?

Air movers and dehumidifiers go in once the water is out and the wet materials are gone. Air movers push air across wet surfaces to speed evaporation. Dehumidifiers pull that moisture out of the air so it does not settle back into the house.

The crew positions equipment based on the moisture map, not just the room size. They may also open small holes behind baseboards to push air into wall cavities, or set up containment with plastic sheeting to focus drying in one area.

Expect the machines to run around the clock. They are loud and they produce warm air. The crew will tell you which outlets they are using and whether anything should stay off, and they will check back over the following days to take new readings and adjust.

Quick answers for Fife and Milton homeowners

Do I need to be home on the first day?

It helps a lot. You know where the water came from, where the shutoffs are, and which belongings matter most. If you cannot be there, arrange for someone who can let the crew in and answer questions.

Can I keep living in the house during drying?

Often, yes, if the damage is limited to part of the home and the water was clean. If the damage is widespread or the water was contaminated, your crew may recommend staying elsewhere.

Should I move furniture before the crew arrives?

Move small items and valuables off wet floors if it is safe to do so. Leave heavy furniture for the crew, who will block it up on pads or move it out of the work area.

Can I turn the drying equipment off at night?

Please do not unless the crew says so. Turning equipment off slows drying and can let moisture settle back into materials.

How will I know when the house is dry?

The crew will take moisture readings on each visit and compare them to dry readings from unaffected areas of your home. Drying is done when those numbers match, not when the surface feels dry.

Why the valley floor matters in Fife and Milton

Homes on flat, low ground drain differently than homes on a slope. In parts of Fife, a heavy rain can leave water standing in yards and against foundations for days, and crawl spaces and garages near the street often see that water first. On Milton's hillside, the bigger issue is often runoff from uphill flowing against the house.

Both situations mean the first day of restoration should include a look outside. Gutters that overflow, downspouts that empty against the foundation, and grading that tips toward the house can all bring water back after the inside is dry.

If water has damaged your Fife or Milton home, request a water damage assessment from ServiceMaster of Tacoma.

Get the help you deserve

We’re available 24/7 to discuss your restoration needs.